| Architecture | Voltage FB |
| Number of channels (#) | 1 |
| Total supply voltage (Min) (+5V=5, +/-5V=10) | 3 |
| Total supply voltage (Max) (+5V=5, +/-5V=10) | 12 |
| GBW (Typ) (MHz) | 140 |
| BW @ Acl (MHz) | 270 |
| Acl, min spec gain (V/V) | 1 |
| Slew rate (Typ) (V/us) | 700 |
| Vn at flatband (Typ) (nV/rtHz) | 11 |
| Vn at 1 kHz (Typ) (nV/rtHz) | 11 |
| Iq per channel (Typ) (mA) | 6 |
| Vos (offset voltage @ 25 C) (Max) (mV) | 5 |
| Rail-to-rail | In to V- |
| Features | Integrated Clamps |
| Rating | Catalog |
| Operating temperature range (C) | -40 to 85 |
| CMRR (Typ) (dB) | 84 |
| Input bias current (Max) (pA) | 20000000 |
| Offset drift (Typ) (uV/C) | 2 |
| Output current (Typ) (mA) | 45 |
| 2nd harmonic (dBc) | 70 |
| 3rd harmonic (dBc) | 57 |
| Frequency of harmonic distortion measurement (MHz) | 5 |
- ?3dB BW (AV = +1) 270 MHz
- Supply Voltage Range 3 V to 12 V
- Slew Rate, (VS = ±5 V) 700 V/μs
- Supply Current 6.2 mA/amp
- Output Current +80/?90 mA
- Input Common-Mode Volt. 0.5 V Beyond V?, 1.7 V
from V+ - Output Voltage Swing (RL = 2 kΩ) 0.8 V from
Rails - Input Voltage Noise 11 nV/√Hz
- Input Current Noise 2.1 pA√Hz/
- DG Error 0.03%
- DP Error 0.10°
- THD (5MHz) ?55 dBc
- Settling Time (0.1%) 37ns
- Fully Characterized for 5 V, and ±5 V
- Output Overdrive Recovery 18 ns
- Output Short Circuit Protected(1)
- No Output Phase Reversal With CMVR Exceeded
VS = 5 V, TA = 25°C, RL = 100 Ω (Typical Values
Unless Specified)
The LMH6657 and LMH6658 devices are low-cost operational amplifiers that operate from a single supply with input voltage range extending below the V?. Based on easy to use voltage feedback topology and boasting fast slew rate (700 V/μs) and high speed (140 MHz GBWP), the LMH6657 (Single) and LMH6658 (dual) can be used in high speed large signal applications. These applications include instrumentation, communication devices, set-top boxes, and so forth.
With a ?3dB BW of 100 MHz (AV = +2) and DG & DP of 0.03% & 0.10° respectively, the LMH6657 and LMH6658 are well suited for video applications. The output stage can typically supply 80 mA into the load with a swing of about 1 V from either rail.
For Industrial applications, the LMH6657 and LMH6658 are excellent cost-saving choices. Input referred voltage noise is low and the input voltage can extend below V? to ease amplification of low level signals that could be at or near the system ground. With low distortion and fast settling, LMH6657 and LMH6658 can provide buffering for A/D and D/A applications.
The LMH6657 and LMH6658 versatility and ease of use is extended even further by offering these high slew rate, high-speed operational amplifiers in miniature packages such as SOT-23-5, SC70, SOIC-8, and VSSOP-8.
