--- 產品詳情 ---
Regulated outputs (#) | 3 |
Vin (Min) (V) | 10.8 |
Vin (Max) (V) | 22 |
Iout (Max) (A) | 3 |
Rating | Catalog |
LDO | 0 |
Features | Voltage Supervisor Circuit, Fault Detection, USB Switch, Programmable Current Limit |
Switching frequency (Typ) (kHz) | 1000 |
Configurability | Software configurable, User programmable |
- Wide Input Supply Voltage Range
(10.8 V - 22 V) - One Adjustable PWM Buck Controller
- 10.8-V – 22-V Input Voltage Range
- 3.3-V – 6.1-V Output Voltage Range
- 500kHz switching frequency
- Type III Compensation
- Programmable Current Limit
- Two Adjustable Step-Down Converter with
Integrated Switching FETs:- 4.75-V - 5.5-V Input
- 0.9-V-3.3-V Output Voltage Range
- 3-A Output Current
- 1-MHz Switching Frequency
- Voltage Scaling Option
- Type III Compensation
- Two 100-m, 0.5-A (TPS65230) 1-A (TPS65231)
USB Switches with Over Current Protection
and Open-Drain Fault Pin - Early Supply Failure Flag (Open Drain Output)
is Set when Input Voltage Drops Below 9.3 V - Early Temperature Warning Flag (Open Drain Output)
is Set if Temperature Approaches Shut-Down Threshold - Supply Voltage Supervisor Circuit with Two
Monitor Inputs and Open Drain Output - Parallel I/O or I2C Control with User Selectable
Address - Advanced Fault Detection and Output Voltage
Adjustment Options in I2C Mode - Pull-Up Current Sources on Buck Enable Pins for Accurate
Start-Up Timing Control with Preset Default - Over Current Protection on All Rails
- Thermal Shutdown to Protect Device During
Excessive Power Dissipation - Thermally Enhanced Package for Efficient
Heat Management (48-pin HTSSOP) - APPLICATIONS
- Digital Set Top Boxes
- xDSL & Cable Modems
- DVD Players
- Home Gateway and Access Point Networks
- Wireless Routers
The TPS652x provides one PWM buck controller, two adjustable, synchronous buck regulators, two independent USB power switches and a supply voltage supervisor (SVS) to provide main power functions for satellite set top boxes, xDSL and cable modem applications operating off a single 12- to 22-V supply.
The SMPS have integrated switching FETs for optimized power efficiency and reduced external component count. Each USB switch provides up to 0.5-A (TPS65230) or 1-A (TPS65231) of current as required by downstream USB devices. All power blocks have thermal and over current/short circuit protection.
The SVS provides two inputs for monitoring positive supply rails. The active-low open-drain output remains low for at least 180 ms after all supply rails rise above their rising edge threshold. Threshold value for VMON1 input is set for monitoring a 3.3-V rail without the need for additional external components. Threshold for VMON2 input is set to 0.8 V and requires resistor dividers on the input to monitor any positive voltage in the system. The nBOR/nHOT open-drain output is pulled low if the input supply drops below 9.3 V or the chip temperature approaches the thermal shutdown limit. This allows the system processor to save critical data and shut down gracefully before the supply fails.
The TPS65230 and TPS65231 can be controlled either through parallel I/Os or through I2C interface. When the pull-up resistor on the USBFLAG2/nINT pin is connected to a 3.3-V or lower supply the I2C interface is disabled and the device is controlled through parallel I/O pins only. With the pull-up resistor connected to 6 V the I2C interface is enabled and the device is controlled by writing to the control registers. Any fault or abnormal operating condition is flagged by the interrupt pin. The interrupt is cleared by reading the status register via the I2C interface.
為你推薦
-
TI數字多路復用器和編碼器SN54HC1512022-12-23 15:12
-
TI數字多路復用器和編碼器SN54LS1532022-12-23 15:12
-
TI數字多路復用器和編碼器CD54HC1472022-12-23 15:12
-
TI數字多路復用器和編碼器CY74FCT2257T2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74LVC257A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74LVC157A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS258A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS257A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74ALS157A2022-12-23 15:12
-
TI數字多路復用器和編碼器SN74AHCT1582022-12-23 15:12
-
【PCB設計必備】31條布線技巧2023-08-03 08:09
相信大家在做PCB設計時,都會發現布線這個環節必不可少,而且布線的合理性,也決定了PCB的美觀度和其生產成本的高低,同時還能體現出電路性能和散熱性能的好壞,以及是否可以讓器件的性能達到最優等。在上篇內容中,小編主要分享了PCB線寬線距的一些設計規則,那么本篇內容,將針對PCB的布線方式,做個全面的總結給到大家,希望能夠?qū)︷B(yǎng)成良好的設計習慣有所幫助。1走線長度1335瀏覽量 -
電動汽車直流快充方案設計【含參考設計】2023-08-03 08:08
-
Buck電路的原理及器件選型指南2023-07-31 22:28
-
100W USB PD 3.0電源2023-07-31 22:27
-
千萬不要忽略PCB設計中線寬線距的重要性2023-07-31 22:27
想要做好PCB設計,除了整體的布線布局外,線寬線距的規則也非常重要,因為線寬線距決定著電路板的性能和穩定性。所以本篇以RK3588為例,詳細為大家介紹一下PCB線寬線距的通用設計規則。要注意的是,布線之前須把軟件默認設置選項設置好,并打開DRC檢測開關。布線建議打開5mil格點,等長時可根據情況設置1mil格點。PCB布線線寬01布線首先應滿足工廠加工能力,1309瀏覽量 -
基于STM32的300W無刷直流電機驅動方案2023-07-06 10:02
-
上新啦!開發板僅需9.9元!2023-06-21 17:43
-
參考設計 | 2KW AC/DC數字電源方案2023-06-21 17:43
-
千萬不能小瞧的PCB半孔板2023-06-21 17:34