資料介紹
The flash boot loader code is executed every time the part is powered on or reset. The
loader can execute the ISP command handler or pass execution to the user application
code.
A LOW level, after reset, at the P0.14 pin is considered as the external hardware request
to start the ISP command handler. The boot loader samples this pin during reset.
Assuming that proper signal is present on X1 pin when the rising edge on RST pin is
generated, it may take up to 3 ms before P0.14 is sampled and the decision on whether to
continue with user code or ISP handler is made. If P0.14 is sampled LOW and the
watchdog overflow flag is set, the external hardware request to start the ISP command
handler is ignored. If there is no request for the ISP command handler execution (P0.14 is
sampled HIGH after reset), a search is made for a valid user program. If a valid user
program is found then the execution control is transferred to it. If a valid user program is
not found, the auto-baud routine is invoked.
Pin P0.14 is used as hardware request for ISP requires special attention. Since P0.14 is in
high impedance mode after reset, it is important that the user provides external hardware
(a pull-up resistor or other device) to put the pin in a defined state. Otherwise unintended
entry into ISP mode may occur.
loader can execute the ISP command handler or pass execution to the user application
code.
A LOW level, after reset, at the P0.14 pin is considered as the external hardware request
to start the ISP command handler. The boot loader samples this pin during reset.
Assuming that proper signal is present on X1 pin when the rising edge on RST pin is
generated, it may take up to 3 ms before P0.14 is sampled and the decision on whether to
continue with user code or ISP handler is made. If P0.14 is sampled LOW and the
watchdog overflow flag is set, the external hardware request to start the ISP command
handler is ignored. If there is no request for the ISP command handler execution (P0.14 is
sampled HIGH after reset), a search is made for a valid user program. If a valid user
program is found then the execution control is transferred to it. If a valid user program is
not found, the auto-baud routine is invoked.
Pin P0.14 is used as hardware request for ISP requires special attention. Since P0.14 is in
high impedance mode after reset, it is important that the user provides external hardware
(a pull-up resistor or other device) to put the pin in a defined state. Otherwise unintended
entry into ISP mode may occur.
下載該資料的人也在下載
下載該資料的人還在閱讀
更多 >
- LPC2000讀寫EEPROM
- LPC12XX FLASH源碼
- 基于NXP LPC2000的次級啟動加載程序解析 1次下載
- LPC2000系列的ARM參考價格 8次下載
- LPC2200_flash內部Flash和外部Flash分散加載 16次下載
- 飛得浦LPC2000系列微處理器介紹 11次下載
- LPC2000系列ARM參考價格 18次下載
- LPC2000系列ARM參考價格 46次下載
- NXP單片機選型指南(英文版) 0次下載
- LPC2000系列單片機學習指導書(英文)
- LPC2000系列ARM硬件結構
- LPC2000系列的CAN總線驗收濾波器應用
- LPC2300/LPC2400 TCP/IP Overvie
- AN10302
- LPC2000 pdf datasheet
- NAND Flash和NOR Flash的區別 1957次閱讀
- FLASH器件特性 FLASH操作的電路原理詳解 7467次閱讀
- 一文了解SPI NAND Flash和SPI NOR Flash的區別 6319次閱讀
- 使用Flash Magic工具燒錄LPC系列MCU(UART/USB/SWD接口) 1w次閱讀
- 不想告別Flash?教你如何繼續使用Flash 1w次閱讀
- 米爾科技NXP LPC1857 LPC1850 Cortex-M3開發板概述 4170次閱讀
- 基于lpc1768的系統時鐘設計 2918次閱讀
- NOR flash和flash有什么不一樣? 1.1w次閱讀
- SPI flash如何運行程序,SPI flash有哪些應用 1.8w次閱讀
- SPI flash是什么,關于SPI FLASH的讀寫問題 10.3w次閱讀
- 對lpc2000系列微控制器片內flash編程的方法 6203次閱讀
- nxp單片機匯總_lpc單片機選型 1.8w次閱讀
- lpc54102的特性 1869次閱讀
- lpc54102引腳圖_lpc54102引腳說明 2083次閱讀
- 從Flash和SRAM中觸發中斷的過程示例 2767次閱讀
下載排行
本周
- 1TC358743XBG評估板參考手冊
- 1.36 MB | 330次下載 | 免費
- 2開關電源基礎知識
- 5.73 MB | 11次下載 | 免費
- 3嵌入式linux-聊天程序設計
- 0.60 MB | 3次下載 | 免費
- 4DIY動手組裝LED電子顯示屏
- 0.98 MB | 3次下載 | 免費
- 5基于FPGA的C8051F單片機開發板設計
- 0.70 MB | 2次下載 | 免費
- 651單片機窗簾控制器仿真程序
- 1.93 MB | 2次下載 | 免費
- 751單片機PM2.5檢測系統程序
- 0.83 MB | 2次下載 | 免費
- 8基于51單片機的RGB調色燈程序仿真
- 0.86 MB | 2次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234315次下載 | 免費
- 2555集成電路應用800例(新編版)
- 0.00 MB | 33566次下載 | 免費
- 3接口電路圖大全
- 未知 | 30323次下載 | 免費
- 4開關電源設計實例指南
- 未知 | 21549次下載 | 免費
- 5電氣工程師手冊免費下載(新編第二版pdf電子書)
- 0.00 MB | 15349次下載 | 免費
- 6數字電路基礎pdf(下載)
- 未知 | 13750次下載 | 免費
- 7電子制作實例集錦 下載
- 未知 | 8113次下載 | 免費
- 8《LED驅動電路設計》 溫德爾著
- 0.00 MB | 6656次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935054次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537798次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420027次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234315次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191186次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183279次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138040次下載 | 免費
評論
查看更多