資料介紹
Table of Contents
General Description
The ADA4355 evaluation system is used to evaluate the performance of the ADA4355 receive uModule . The system couples the Analog Devices ADA4355 evaluation board to a Xilinx KC705 FPGA evaluation platform. The KC705 provides ample memory, GPIOs and processing power to perform all control and data manipulation functions. All evaluation system control and data processing is easily accomplished via a MATLAB-based, highly intuitive graphical user interface. Figure 1. ADA4355 Evaluation System
Getting Started
Installing the Software
Install the software before connecting the FMC communication board to the USB port of the PC.
When the software is installed the default location will be C:/Program Files/Analog Devices/ADA4355. If you do not have write privileges at this location choose another location where you do have write privileges, typically under “C:/Users/
- Start the Windows Operating System and download the software, ADA4355 Evaluation Software, provided below.
- Choose the folder location for installation as shown in figure 3 and click Next. If desired a shortcut can be added to the PC desktop.
Reminder: The software must be installed in a location where you have write privileges. Figure 3. - The evaluation software requires a MATLAB Runtime engine. If the MATLAB Runtime engine is already installed, this step is skipped. Choose the location for the installation of the Runtime engine and click Next.
- Accept the MathWorks software license agreement as shown in Figure 4 and click Next. The Runtime engine download is about 700MB. Ensure there is sufficient free hard drive space on the PC.Figure 4.
- Connect and power up the evaluation system as described on the Powering Up section.
Hardware
ADA4355 Evaluation System
Figure 6. ADA4355 Evaluation System
- 12V FPGA board supply and on/off switch
- 5V ADA4355 evaluation board supply (See figure 7)
- Optional external photo diode (APD) voltage supply connector (see figure 8)
- DC2159A communication interface board USB port.
- ADA4355 receive uModule.
Figure 7. Evaluation board 5V connection detail
Figure 8. Optional high-voltage photo detector bias voltage connection detail (Header P5 and Resistor R7)
Powering Up
The ADA4355 evaluation system requires two power supplies, a 12V supplyfor the FPGA board and a clean, well-regulated, 5V supply (user to provide) for the ADA4355 board. Additionally, a high voltage supply is needed to reverse bias the photo detector. The evaluation system includes an on-board high-voltage bias generator that is fully controlled via the GUI. Alternatively, the user has the option to supply their own photo detector bias voltage through header P5. All connection points are indicated in Figure 6. Detail for the 5V supply connection is also shown in Figure 7 while detail for the optional, user-supplied, high-voltage reverse bias connection (HV) is shown in Figure 8. If supplying your own photo detector reverse bias voltage, the 10? resistor R7 (shown in Figure 8) should be removed from the ADA4355 evaluation board prior to making any supply connections. Evaluation system connection instructions are as follows:
- Connect the 12V supply to the FPGA board.
- Connect the included USB cable from the PC to the USB port on the LTC communication interface board.
- Connect the user provided 5V power supply to the ADA4355 evaluation board. See Figure 7 for connection details.
- If using the on-board bias generator (default) then skip this step and leave header P5 unconnected.If providing your own photo detector reverse bias voltage be sure that 10? resistor R7 has been removed and apply the desired reverse bias voltage at pin 1 (HV) of header P5. See Figure 8 for R7 location and header P5 connection details.
Software Operation
Setup and Measurement Configuration
- Start up the software by double clicking the desktop shortcut (if present), or navigate to the directory location chosen during installation, and under the application subfolder, run ADA4355.exe.
You may also Search in all programs for ADA4355.exe to launch the software.
Due to initialization of the MATLAB runtime engine initial start-up after reboot could take up to 2 minutes. - The There are two panels. Main Panel and FFT Panel.
Main Panel is shown in Figure 11 and controls the following settings
Figure 11. Main Panel Settings.
- Gain drop down menu is used to set the gain of the TIA.
- LPF drop down menu is used to set the Analog Low Pass Filter inside the ADA4355.
- Current Driver On radio button is used to enable or disable the laser driver from pulsing the laser.
- PD Voltage drop down menu is used to set the Reverse Bias Voltage of the Photo Detector when using the on-board APD bias generator.
- DC Current drop down menu is used to set the DC current through the laser diode. This biases the laser to a threshold level just below the current level where the laser would begin to emit light. The default and recommended level for the included laser diode is 10mA. See Figure 11 and Figure 12.
- Pulsed Current drop down menu is used to set the pulsed current through the laser diode. See Figure 11 and Figure 12.
- Averages drop down menu is used to set the number of data frames averaged for the measurement result.
- Configure & Run is used to start the measurement any time measurement settings are changed.
- Enable is used to enable a moving average filter on the collected data.
- Window Size sets the number of samples in the moving average filter.
- Equivalent BW is the bandwidth of the moving average filter and is shown for convenience.
Making a Measurment
Once the measurement configurations are selected, click the Configure & Run button. A pop-up window is displayed with the remaining time of the measurement. Once the data is collected it is plotted as shown in figure 15. Figure 15.
Moving Average Filter
Once the measurement is done and the data is plotted, checking the Enable radio button, as shown in Figure 16, will apply a moving average filter on the data. Change the Window Size and click the Filter button to update the filter window size (number of samples averaged). Figure 16.
Axes Configuration
The Axes Configuration panel is shown in Figure 17. The X-Lower Limit and X-Upper Limit set the lower and upper y-axis limits respectively.
The Y-Lower Limit and Y-Upper Limit set the lower and upper y-axis limits respectively.
When any changes are made in the Axes Configuration panel the Configure Axes button is enabled and must be clicked for the changes to take place. Figure 17
Cursors
In the top left corner of the plot the Cursors radio button enables two vertical cursors to appear on the plot.
When the Cursors radio button is checked the cursors data is displayed underneath the legend as shown in Figure 18. The X and Y location of the cursors is shown as well as the delta X, delta Y, and ratio of the two deltas.
To slide the cursor click and hold on the intended cursor and move the mouse to the intended location.
By default, the cursors are tracking the raw data (blue curve). To track the filtered data (orange curve) click anywhere on the filtered data. The filtered data momentarily flashes and the color of the vertical cursor lines changes to match the color of the data trace they are tracking.
Figure 18. Cursor functionality
FFT Panel
Once data is collected FFT Panel tab appears at the top of the main. Click FFT Panel tab, an FFT is run on the data and the FFT result appear.
Figure 19. FFT Panel
Tool Bar
The Tool Bar is located on the top left corner of the GUI.
Selecting Zoom-in toggle and clicking on the plot will zoom in and center at the mouse location. Alternatively, click and drag to draw a box around the area to zoom. When the mouse button is released the axes zoom in to the region enclosed by the box.
The Zoom-out toggle works in the same manner but zooms out.
Each mouse click zooms in or out by a factor of 2.
While Zoom in or Zoom out is enabled right click on the main plot and select Reset to Original View to go back to the original axes limits.
The Pan toggle (hand) turns on the pan mode for axes in the main plot.
The Save toggle (floppy disk) saves the Raw Voltage data sampled by the ADC.
Figure 20. Tool Bar
Downloads
声明:本文内容及配图由入驻作者撰写或者入驻合作网站授权转载。文章观点仅代表作者本人,不代表电子发烧友网立场。文章及其配图仅供工程师学习之用,如有内容侵权或者其他违规问题,请联系本站处理。 举报投诉
- ADA4571R-EBZ用户指南18次下载
- Ethereum Wiki以太坊Wiki目录1次下载
- ADF4355ADF4355-2ADF4355-3ADF4356ADF5355ADF5356评估软件10次下载
- AN-1353:如何绕过ADF4355-2、ADF4355、ADF4355-3、ADF4356、ADF5355和ADF5356的压控振荡器校准8次下载
- UG-1537:EVAL-ADA458EBZ用户指南0次下载
- UG-132:ADA492x-1和ADA493x-1系列差分放大器评估板用户指南2次下载
- UG-1481:EVAL-ADA4625-2ARDZ用户指南2次下载
- ADIS16IMU2/PCBZ Wiki指南8次下载
- CN0416-用户指南Wiki15次下载
- CN0435用户指南Wiki1次下载
- ADIS1650x/PCBZ Wiki指南2次下载
- ADRV9009-ZU11G RF-SOM-wiki用户指南10次下载
- UG-132:ADA492x-1和ADA493x-1系列差分放大器评估板用户指南1次下载
- ADA4355: Programmable Transimpedance, Current to Bits Receiver μModule Data Sheet4次下载
- PSMC设计器用户指南及技巧4次下载
- CD100M满杯检测方案的安装指南666次阅读
- Air780EP模块AT开发-HTTP应用指南662次阅读
- 电工必备接线指南:轻松掌握各种电路接线技巧3309次阅读
- NVIDIA RTX 5000 Ada显卡性能实测报告7616次阅读
- 微弱电流测量-ADA4530使用要点5016次阅读
- ADA4350如何实现串口读写924次阅读
- 滤波器设计指南2403次阅读
- 如何在Ubuntu 20.04安装Gitea1674次阅读
- NVIDIA Ada架构上的视频性能提升和更高保真度1881次阅读
- 为什么电子指南针能指示方向1935次阅读
- 使用含快速开关SiC器件的RC缓冲电路实用解决方案和指南2843次阅读
- 差分放大器ADA4932和ADA4950的性能特点及应用范围3120次阅读
- 怎么搭建zedboard的编译环境?1806次阅读
- ADC LTC2185 + 差分放大器 ADA4927之间的“芯”故事8801次阅读
- ADA4896:ADI轨到轨输出放大器详解5957次阅读
下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
評論
查看更多