資料介紹
Table of Contents
ADIS16IMU2/PCBZ Breakout Board Wiki-Guide
GENERAL DESCRIPTION
The ADIS16IMU2/PCBZ is a breakout board that provides the ability to connect with the following products, using a standard ribbon cable (16-pin, 1mm pitch): ADIS16334, ADIS16362, ADIS16364, ADIS16365, ADIS16367, ADIS16405, ADIS16407, ADIS16445. This breakout board simplifies connection to an embedded processor system, early in the development cycle and also connects this products to the EVAL-ADIS2 evaluation system.
SETUP WITH ADIS1633X/44X IMUS
Connecting the IMU (ADIS16334, ADIS16445 or ADIS16448), ADIS1644X/FLEX and ADIS16IMU2 together is a very simple two-step process. Please note that the pin numbers markings on the ADIS1644X/FLEX were incorrect in early manufacturing lots. Please ignore the pin number markings on the ADIS1644X/FLEX and use the following instructions to guide the connection process.
Step 1: ADIS16xxx (IMU) to ADIS1644X/FLEX
The following diagram illustrates the two different connectors on ADIS1644X/FLEX, along with their connections:
The following diagram shows the IMU's interface connector, which the ADIS1644X/FLEX connects with:
The following table shows the correct insertion, along with the three most common incorrect ways to insert the flex onto the IMU's interface connector
Step 2: ADIS1644X/FLEX to ADIS16IMU2/PCBZ
The ADIS1644X/FLEX has 20 pins, while J2 on the ADIS16IMU2/PCBZ has 24-pins. Connect the flex to pins 1 through 20 on J2. Pin numbers 1, 2, 23 and 24 are clearly identified on the silk screen, which is associated with J2 on the ADIS16IMU2/PCBZ. The following pictures illustrate the correct insertion alignment for this connection
Here is an example of what this will look like, after finishing these steps:
SETUP WITH ADIS1636x/40X IMUs
Connecting any of the ADIS1636x or ADIS1640x IMU products is very simple, as J2 mates perfectly with the interface connect on these products. Click on any of the images to below for larger views.
For more information on proper handling of the ADIS1636x and ADIS1640x packages, please consult AN-1045
KEY PHYSICAL DIMENSIONS
INTERFACE CONNECTOR
J1 is the electrical connector that provides direct access to power, ground and critical digital I/O pins on the devices. It is a 16-pin, dual-row, 2-mm pitch connector that support 1mm ribbon cable systems.
Pin Assignments
Here is the pin assignments for J1, which is the connector that will interface with an embedded processor board.
Ribbon Cable Options
Check out the following link for ideas on how to make or purchase 16-pin, 1mm ribbon cables that can mate to the ADIS16IMU2/PCBZ.
ELECTRICAL SCHEMATIC
SUPPORT
If you have any questions in using this evaluation tool, please visit the Inertial MEMS Community, inside of the Inertial MEMS Sesnor Community EngineerZone. If you are unable to find an answer to your question through the search tools in this forum, please feel free to post a new question. As always, the quality of detail in the original request will relate to the quality of the support that forum can provide. We thank you for your business and look forward to seeing what you create with this technology!
- 基于ADIS1620x/PCBZ加速計的
- EVADIIS16407 ADIS16407/PCB 分線板
- EVAD16367 ADIS16367/PCB 分線板
- EVAR-ADIS16365 ADIS16365/PCB 分線板
- EVAR-ADIS16362 ADIS16362/PCB分線板
- EVADIIS16405 ADIS16405/PCB 分線板
- EVAD16334 ADIS16334/PCB分線板
- ADIS16448/PCBZ數據表
- ADIS16405/PCBZ數據表
- ADIS16260/ADIS16265/PCBZ數據表
- ADIS16300/PCBZ數據表
- ADIS16220/PCBZ數據表
- ADIS1650x/PCBZ Wiki指南
- 基于ADIS16203/PCBZ加速計的參考設計
- 基于ADIS16201/PCBZ加速計的參考設計
- RA6T2的16位模數轉換器操作 [11] 配置RA6T2 ADC模塊 (8) 177次閱讀
- RA6T2的16位模數轉換器操作 [10] 配置RA6T2 ADC模塊 (7) 187次閱讀
- RA6T2的16位模數轉換器操作 [8] 配置RA6T2 ADC模塊 (5) 189次閱讀
- RA6T2的16位模數轉換器操作 [7] 配置RA6T2 ADC模塊 (4) 180次閱讀
- RA6T2的16位模數轉換器操作 [5] 配置RA6T2 ADC模塊 (2) 230次閱讀
- RA6T2的16位模數轉換器操作 [2] A/D轉換器概述 (2) 224次閱讀
- 一種易于實現的無外部設備IMU校準方法 1182次閱讀
- MEMS IMU/陀螺儀對準的基礎知識 4384次閱讀
- EVAL-2QR0665G-28W16V開關電源功能分析 5803次閱讀
- 基于MEMS技術的IMU慣性測量單元的工作原理解析 1.1w次閱讀
- 慣性測量裝置IMU的用途_IMU在主機應用處理器的功能 1w次閱讀
- 自動駕駛技術IMU的基礎知識和應用場景 7736次閱讀
- IMU中傳感器的功能_IMU應用實例_IMU解決方案 2.7w次閱讀
- 16x2點陣字符液晶模塊設計實現 1380次閱讀
- MEMS慣性測量單元(IMU)/陀螺儀對準基礎 3968次閱讀
下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
評論
查看更多