電子發燒友網>電子資料下載>類型>參考設計>CN0235 FMC-SDP轉接器和評估板/Xilinx KC705參考設計

CN0235 FMC-SDP轉接器和評估板/Xilinx KC705參考設計

1947137 2021-05-22 | pdf | 352.54KB | 次下載 | 2積分

資料介紹

This version (09 Jan 2021 00:55) was approved by Robin Getz.The Previously approved version (31 Dec 2020 06:00) is available.

CN0235 FMC-SDP Interposer & Evaluation Board / Xilinx KC705 Reference Design
- Supported Devices
- Reference Circuits
Overview
- More information
Getting Started
Run the Demonstration Project
More information

CN0235 FMC-SDP Interposer & Evaluation Board / Xilinx KC705 Reference Design

Reference Circuits

CN0235

Overview

This document presents the steps to setup an environment for using the EVAL-CN0235-SDPZ evaluation board together with the Xilinx KC705 FPGA board and the Xilinx Embedded Development Kit (EDK). Below is presented a picture of the EVAL-CN0235-SDPZ Evaluation Board with the Xilinx KC705 board.

For component evaluation and performance purposes, as opposed to quick prototyping, the user is directed to use the part evaluation setup. This consists of:

1. A controller board like the SDP-B ( EVAL-SDP-CS1Z)
2. The component SDP compatible product evaluation board
3. Corresponding PC software ( shipped with the product evaluation board)

The SDP-B controller board is part of Analog Devices System Demonstration Platform (SDP). It provides a high speed USB 2.0 connection from the PC to the component evaluation board. The PC runs the evaluation software. Each evaluation board, which is an SDP compatible daughter board, includes the necessary installation file required for performance testing.

Note: it is expected that the analog performance on the two platforms may differ.

28 Sep 2012 10:32 · Adrian Costina

Below is presented a picture of SDP-B Controller Board with the EVAL-CN0235-SDPZ Evaluation Board.

The CN0235 board is a fully isolated lithium ion battery monitoring and protection system. Lithium ion (Li-Ion) battery stacks contain a large number of individual cells that must be monitored correctly in order to enhance the battery efficiency, prolong the battery life, and ensure safety.

The AD7280A contains all the functions required for general-purpose monitoring of stacked lithium ion batteries as used in hybrid electric vehicles, battery backup applications, and power tools. The part has multiplexed cell voltage and auxiliary ADC measurement channels for up to six cells of battery management. An internal ±3 ppm/°C reference is provided that allows a cell voltage accuracy of ±1.6 mV. The ADC resolution is 12 bits and allows conversion of up to 48 cells within 7 us.

The AD8280 is a hardware-only safety monitor for lithium ion battery stacks. The part has inputs to monitor six battery cells and two temperature sensors (either NTC or PTC thermistors). The part is designed to be daisy-chained with other AD8280 devices to monitor a stack of significantly more than six cells without the need for numerous isolators. Its output can be configured for an independent or shared alarm state.

More information

CN0235 Product Info - pricing, samples, datasheet
AD7280A Product Info - pricing, samples, datasheet
AD8280 Product Info - pricing, samples, datasheett
EVAL-CN0235-SDPZ evaluation board user guide
Xilinx KC705 FPGA board

Getting Started

The first objective is to ensure that you have all of the items needed and to install the software tools so that you are ready to create and run the evaluation project.

Required Hardware

Xilinx KC705 FPGA board
FMC-SDP adapter board
EVAL-CN0235-SDPZ evaluation board

Required Software

Xilinx ISE 14.6.
UART Terminal (Termite/Tera Term/Hyperterminal), baud rate 115200.
The EVAL-CN0235 reference project for Xilinx KC705 FPGA.

Downloads

AD7280A Driver: https://github.com/analogdevicesinc/no-OS/tree/master/device_drivers/AD7280A
CN0235 Commands: https://github.com/analogdevicesinc/no-OS/tree/master/device_commands/CN0235
Xilinx Boards Common Drivers: https://github.com/analogdevicesinc/no-OS/tree/master/platform_drivers/Xilinx/SDP_Common
EDK KC705 Reference project: https://github.com/analogdevicesinc/fpgahdl_xilinx/tree/master/cf_sdp_kc705

Run the Demonstration Project

Hardware setup

Before connecting the ADI evaluation board to the Xilinx KC705 make sure that the VADJ_FPGA voltage of the KC705 is set to 3.3V. For more details on how to change the setting for VADJ_FPGA visit the Xilinx KC705 product page.

Use the FMC-SDP interposer to connect the ADI evaluation board to the Xilinx KC705 board on the FMC LPC connector.
Connect the JTAG and UART cables to the KC705 and power up the FPGA board.

Reference Project Overview

The following commands were implemented in this version of EVAL-CN0235 reference project for Xilinx KC705 FPGA board.

Command	Description
help?	Displays all available commands.
adcCode?	Displays the ADC code of one channel from selected device. Accepted values: device: 0 - master 1 - slave register address: 0 - Cell Voltage 1 1 - Cell Voltage 2 2 - Cell Voltage 3 3 - Cell Voltage 4 4 - Cell Voltage 5 5 - Cell Voltage 6 6 - AUX ADC 1 7 - AUX ADC 2 8 - AUX ADC 3 9 - AUX ADC 4 10 - AUX ADC 5 11 - AUX ADC 6
voltage?	Displays the input voltage of one channel from selected device. Accepted values: device: 0 - master 1 - slave register address: 0 - Cell Voltage 1 1 - Cell Voltage 2 2 - Cell Voltage 3 3 - Cell Voltage 4 4 - Cell Voltage 5 5 - Cell Voltage 6 6 - AUX ADC 1 7 - AUX ADC 2 8 - AUX ADC 3 9 - AUX ADC 4 10 - AUX ADC 5 11 - AUX ADC 6
register?	Displays the content of one register from selected device. Accepted values: device: 0 - master 1 - slave register address: 13 - Control high byte 14 - Control low byte 15 - Cell Overvoltage 16 - Cell Undervoltage … (see AD7280A_Datasheet p.28) 29 - CNVST Control
register=	Sets the content of one register from selected device. Accepted values: device: 0 - master 1 - slave register address: 13 - Control high byte 14 - Control low byte 15 - Cell Overvoltage 16 - Cell Undervoltage … (see AD7280A_Datasheet p.28) 29 - CNVST Control register value: 0 .. 255 - value to be written inside the register.
selfTestAD7280A!	Performs the self test for both AD7280A devices on the board (one master and one slave).
alertPinAD7280A?	Reads the status of Alert Pin from AD7280A.
enableAD8280=	Enables/disables the AD8280 device. Accepted values: 0 - disable the AD8280 device 1 - enable the AD8280 device
alarmPinOvAD8280?	Reads the status of Overvoltage Alarm Pin from AD8280.
alarmPinUvAD8280?	Reads the status of Undervoltage Alarm Pin from AD8280.
selfTestAD8280!	Performs the self test for both AD8280 devices on the board (one master and one slave).

Commands can be executed using a serial terminal connected to the UART peripheral of Xilinx KC705 FPGA.

The following image shows a generic list of commands in a serial terminal connected to Xilinx KC705 FPGA's UART peripheral.

Software Project Setup

The hardware platform for each reference projects with FMC-SDP interposer and KC705 evaluation board is common. The next steps should be followed to recreate the software project of the reference design:

First download the KC705 Reference project from Github on your computer. You can do this by clonning this repository: https://github.com/analogdevicesinc/fpgahdl_xilinx.

From this entire repository you will use cf_sdp_kc705 folder. This is common for all KC705 projects.

Open the Xilinx SDK. When the SDK starts, it asks you to provide a folder where to store the workspace. Any folder can be provided. Make sure that the path where it is located does not contain any spaces.
In the SDK select the File→Import menu option to import the software projects into the workspace.

In the Import window select the General→Existing Projects into Workspace option.

In the Import Projects window select the cf_sdp_kc705 folder as root directory and check the Copy projects into workspace option. After the root directory is chosen the projects that reside in that directory will appear in the Projects list. Press Finish to finalize the import process.

The Project Explorer window now shows the projects that exist in the workspace without software files.

Now the software must be added in your project. For downloading the software, you must use 3 links from Github given in Downloads section. From there you'll download the specific driver, the specific commands and the Xilinx Boards Common Drivers(which are commons for all Xilinx boards). All the software files downloaded must be copied in src folder from sw folder.

Before compilation in the file called Communication.h you have to uncomment the name of the device that you currently use. In the picture below there is an example of this, which works only with AD5629R project. For another device, uncomment only the respective name. You can have one driver working on multiple devices, so the drivers's name and the uncommented name may not be the same for every project.

The SDK should automatically build the project and the Console window will display the result of the build. If the build is not done automatically, select the Project→Build Automatically menu option.
If the project was built without any errors, you can program the FPGA and run the software application.

13 Aug 2013 09:22 · Lucian Sin