電子發燒友網>電子資料下載>類型>參考設計>AD5398穩壓器電流宿DAC Linux驅動程序

AD5398穩壓器電流宿DAC Linux驅動程序

2076814 2021-05-23 | pdf | 56.92KB | 次下載 | 3積分

資料介紹

This version (11 Feb 2016 21:16) was approved by Lars-Peter Clausen.The Previously approved version (05 Sep 2012 14:17) is available.

AD5398 Regulator Current Sink DAC Linux Driver
Supported Devices
Evaluation Boards
Description
Source Code
Status
Files
Adding Linux driver support
- Customize Device Parameters
- Driver Testing

AD5398 Regulator Current Sink DAC Linux Driver

Evaluation Boards

EVAL-AD5821EBZ

Description

AD5398 and AD5821 is a single 10-bit DAC with 120mA output current sink capability. I2C bus is connected to enable/disable output and set the proper output current value. This driver adapts to voltage and current regulator framework in Linux kernel.

Source Code

Status

Source	Mainlined?
git	Yes

Files

Function	File
driver	drivers/regulator/ad5398.c

Adding Linux driver support

Configure kernel with “make menuconfig” (alternatively use “make xconfig” or “make qconfig”)

The AD5398/AD5821 Driver depends on CONFIG_I2C

Select voltage and current regulator framework support and enable AD5398/AD5821 driver. Don't forget to select virtual regulator consumer and userspace regulator consumer as module. Because AD5398 driver is loaded after I2C bus finish initialization at kernel booting, built-in consumers may be loaded earlier and find supply in AD5398 driver is not available.

Linux Kernel Configuration
	Device Drivers  --->
		[*] Voltage and Current Regulator Support  --->
		   Virtual regulator consumer support
		   Userspace regulator consumer support
		<*>   Analog Devices AD5398/AD5821 regulators

Customize Device Parameters

The platform info defined in bf537-stamp board file is for ad5398 and ad5821 only. If you want to customize this driver for other compatible current regulator DAC, you should revise the platform information accordingly.

Define device supply name exported by the driver.

Define supply value range.

Define supply name in platform_data for the virtual consumer to match and use.

Define supply name for the user space consumer to match and use.

Driver Testing

Check regulator driver initialization information at kernel booting.

This specifies any shell prompt running on the target

regulator: core version 0.5
i2c /dev entries driver
regulator: isink: 0 <--> 120 mA
ad5398 0-000c: ad5398 regulator driver loaded
i2c-bfin-twi i2c-bfin-twi.0: Blackfin BF5xx on-chip I2C TWI Contoller, regs_base@ffc01400

Check if AD5398 is probed properly.

This specifies any shell prompt running on the target

root:/> ls -l sys/class/regulator/regulator.0/
lrwxrwxrwx    1 root     root            0 Jan  1 19:47 device -> ../../../0-000c
-r--r--r--    1 root     root         4096 Jan  1 19:47 max_microamps
-r--r--r--    1 root     root         4096 Jan  1 19:47 microamps
-r--r--r--    1 root     root         4096 Jan  1 19:47 min_microamps
-r--r--r--    1 root     root         4096 Jan  1 19:47 name
-r--r--r--    1 root     root         4096 Jan  1 19:47 num_users
drwxr-xr-x    2 root     root            0 Jan  1 19:47 power
-r--r--r--    1 root     root         4096 Jan  1 19:47 requested_microamps
-r--r--r--    1 root     root         4096 Jan  1 19:47 state
lrwxrwxrwx    1 root     root            0 Jan  1 19:47 subsystem -> ../../../../../../../class/regulator
-r--r--r--    1 root     root         4096 Jan  1 19:47 suspend_disk_state
-r--r--r--    1 root     root         4096 Jan  1 19:47 suspend_mem_state
-r--r--r--    1 root     root         4096 Jan  1 19:47 suspend_standby_state
-r--r--r--    1 root     root         4096 Jan  1 19:47 type
-rw-r--r--    1 root     root         4096 Jan  1 19:47 uevent
root:/> cat sys/class/regulator/regulator.0/max_microamps
120000
root:/> cat sys/class/regulator/regulator.0/min_microamps
0
root:/> cat sys/class/regulator/regulator.0/name
current range
root:/> cat sys/class/regulator/regulator.0/type
current
root:/> cat sys/class/regulator/regulator.0/state
disabled

Insert virtual consumer driver module and check usability.

This specifies any shell prompt running on the target

root:/> modprobe virtual
root:/> ls -l sys/devices/platform/reg-virt-consumer.0/
lrwxrwxrwx    1 root     root            0 Jan  1 21:23 driver -> ../../../bus/platform/drivers/reg-virt-consumer
-rw-rw-rw-    1 root     root         4096 Jan  1 21:23 max_microamps
-rw-rw-rw-    1 root     root         4096 Jan  1 21:23 max_microvolts
-r--r--r--    1 root     root         4096 Jan  1 21:23 microamps_requested_current
-rw-rw-rw-    1 root     root         4096 Jan  1 21:23 min_microamps
-rw-rw-rw-    1 root     root         4096 Jan  1 21:23 min_microvolts
-r--r--r--    1 root     root         4096 Jan  1 21:23 modalias
-rw-rw-rw-    1 root     root         4096 Jan  1 21:23 mode
drwxr-xr-x    2 root     root            0 Jan  1 21:23 power
lrwxrwxrwx    1 root     root            0 Jan  1 21:23 subsystem -> ../../../bus/platform
-rw-r--r--    1 root     root         4096 Jan  1 21:23 uevent
root:/> cat sys/devices/platform/reg-virt-consumer.0/max_microamps
120000
root:/> cat sys/devices/platform/reg-virt-consumer.0/min_microamps
0
root:/> echo 50000 > sys/devices/platform/reg-virt-consumer.0/min_microamps
root:/> cat sys/devices/platform/reg-virt-consumer.0/min_microamps
50000
root:/> cat sys/devices/platform/reg-virt-consumer.0/max_microamps
120000

Insert user space consumer driver module and check usability.

This specifies any shell prompt running on the target

root:/> modprobe userspace-consumer
root:/> ls -l sys/devices/platform/reg-userspace-consumer.0/
lrwxrwxrwx    1 root     root            0 Jan  1 21:26 driver -> ../../../bus/platform/drivers/reg-userspace-consumer
-r--r--r--    1 root     root         4096 Jan  1 21:26 microamps_requested_current
-r--r--r--    1 root     root         4096 Jan  1 21:26 modalias
-r--r--r--    1 root     root         4096 Jan  1 21:26 name
drwxr-xr-x    2 root     root            0 Jan  1 21:26 power
-rw-r--r--    1 root     root         4096 Jan  1 21:26 state
lrwxrwxrwx    1 root     root            0 Jan  1 21:26 subsystem -> ../../../bus/platform
-rw-r--r--    1 root     root         4096 Jan  1 21:26 uevent
root:/> cat sys/devices/platform/reg-userspace-consumer.0/name
ad5398
root:/> cat sys/devices/platform/reg-userspace-consumer.0/state
disabled
root:/> echo enabled > sys/devices/platform/reg-userspace-consumer.0/state
root:/> cat sys/devices/platform/reg-userspace-consumer.0/state
enabled

To control ADC to output a given current, you only need to set the value to sysfs entry min_microamps in virtual consumer platform device. The driver adjusts the output according to the min current value received.

声明：本文内容及配图由入驻作者撰写或者入驻合作网站授权转载。文章观点仅代表作者本人，不代表电子发烧友网立场。文章及其配图仅供工程师学习之用，如有内容侵权或者其他违规问题，请联系本站处理。举报投诉

下載該資料的人也在下載下載該資料的人還在閱讀

更多 >