資料介紹
Table of Contents
AD5449 IIO DAC Linux Driver
Supported Devices
Reference Circuits
Evaluation Boards
Description
This is a Linux industrial I/O (IIO) subsystem driver, targeting single channel serial interface DACs. The industrial I/O subsystem provides a unified framework for drivers for many different types of converters and sensors using a number of different physical interfaces (i2c, spi, etc). See IIO for more information.
Source Code
Status
Files
Function | File |
---|---|
driver | drivers/iio/dac/ad5449.c |
include | include/linux/platform_data/ad5449.h |
Example platform device initialization
Specifying reference voltage via the regulator framework
Below example specifies a 2.5 Volt reference for the SPI device 3 on SPI-Bus 0. (spi0.3)
#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) static struct regulator_consumer_supply ad5449_consumer_supplies[] = { REGULATOR_SUPPLY("vcc", "spi0.3"), }; ? static struct regulator_init_data stamp_avdd_reg_init_data = { .constraints = { .name = "2V5", .valid_ops_mask = REGULATOR_CHANGE_STATUS, }, .consumer_supplies = ad5449_consumer_supplies, .num_consumer_supplies = ARRAY_SIZE(ad5449_consumer_supplies), }; ? static struct fixed_voltage_config stamp_vdd_pdata = { .supply_name = "board-2V5", .microvolts = 2500000, .gpio = -EINVAL, .enabled_at_boot = 0, .init_data = &stamp_avdd_reg_init_data, }; ? static struct platform_device brd_voltage_regulator = { .name = "reg-fixed-voltage", .id = -1, .num_resources = 0, .dev = { .platform_data = &stamp_vdd_pdata, }, }; ? #endif
static struct platform_device *board_devices[] __initdata = { #if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) &brd_voltage_regulator #endif };
static int __init board_init(void) { [--snip--] ? platform_add_devices(board_devices, ARRAY_SIZE(board_devices)); ? [--snip--] ? return 0; } arch_initcall(board_init);
Declaring SPI slave devices
Unlike PCI or USB devices, SPI devices are not enumerated at the hardware level. Instead, the software must know which devices are connected on each SPI bus segment, and what slave selects these devices are using. For this reason, the kernel code must instantiate SPI devices explicitly. The most common method is to declare the SPI devices by bus number.
This method is appropriate when the SPI bus is a system bus, as in many embedded systems, wherein each SPI bus has a number which is known in advance. It is thus possible to pre-declare the SPI devices that inhabit this bus. This is done with an array of struct spi_board_info, which is registered by calling spi_register_board_info().
For more information see: Documentation/spi/spi-summary
Depending on the converter IC used, you may need to set the modalias accordingly, matching your part name.
It may also required to adjust max_speed_hz. Please consult the datasheet, for maximum spi clock supported by the device in question.
static struct spi_board_info board_spi_board_info[] __initdata = { { /* the modalias must be the same as spi device driver name */ .modalias = "ad5449", /* Name of spi_driver for this device */ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, /* Framework bus number */ .chip_select = 3, /* Framework chip select */ .mode = SPI_MODE_2, }, };
static int __init board_init(void) { [--snip--] ? spi_register_board_info(board_spi_board_info, ARRAY_SIZE(board_spi_board_info)); ? [--snip--] ? return 0; } arch_initcall(board_init);
Adding Linux driver support
Configure kernel with “make menuconfig” (alternatively use “make xconfig” or “make qconfig”)
The AD5449 Driver depends on CONFIG_SPI
Linux Kernel Configuration Device Drivers ---> ... <*> Industrial I/O support ---> --- Industrial I/O support ... Digital to analog converters ---> ... <*> Analog Devices AD5449 and similar DACs drive ... ... ...
Driver testing
Each and every IIO device, typically a hardware chip, has a device folder under /sys/bus/iio/devices/iio:deviceX. Where X is the IIO index of the device. Under every of these directory folders reside a set of files, depending on the characteristics and features of the hardware device in question. These files are consistently generalized and documented in the IIO ABI documentation. In order to determine which IIO deviceX corresponds to which hardware device, the user can read the name file /sys/bus/iio/devices/iio:deviceX/name. In case the sequence in which the iio device drivers are loaded/registered is constant, the numbering is constant and may be known in advance.
This specifies any shell prompt running on the target
root:/> cd /sys/bus/iio/devices/ root:/sys/bus/iio/devices> ls iio:device0 root:/sys/bus/iio/devices> cd iio:device0 root:/sys/devices/platform/bfin-spi.0/spi0.3/iio:device0> ls -l -r--r--r-- 1 root root 4096 Jan 1 02:20 dev -r--r--r-- 1 root root 4096 Jan 1 02:20 name -rw-r--r-- 1 root root 4096 Jan 1 02:25 out_voltage0_raw -rw-r--r-- 1 root root 4096 Jan 1 02:20 out_voltage0_scale -rw-r--r-- 1 root root 4096 Jan 1 02:25 out_voltage1_raw -rw-r--r-- 1 root root 4096 Jan 1 02:20 out_voltage1_scale drwxr-xr-x 2 root root 0 Jan 1 02:20 power lrwxrwxrwx 1 root root 0 Jan 1 02:20 subsystem -> ../../../../../../../bus/iio -rw-r--r-- 1 root root 4096 Jan 1 02:20 uevent
For DACs with only one output channel there will be no out_voltage1_raw and out_voltage1_scale files
Show device name
This specifies any shell prompt running on the target
root:/sys/devices/platform/bfin-spi.0/spi0.3/iio:device0> cat name ad5449
Show scale
Description:
scale to be applied to out_voltage0_raw in order to obtain the measured voltage in millivolts.
This specifies any shell prompt running on the target
root:/sys/devices/platform/bfin-spi.0/spi0.3/iio:device0> cat out_voltage_scale 0.152
Set channel 0
Description:
/sys/bus/iio/devices/iio:deviceX/out_voltageY_raw
Raw (unscaled, no bias etc.) output voltage for channel Y.
This specifies any shell prompt running on the target
root:/sys/devices/platform/bfin-spi.0/spi0.3/iio:device0> echo 1234 > out_voltage0_raw
U = out_voltage0_raw * out_voltage_scale = 1234 * 0.152mV = 187.568 mV
More Information
- IIO mailing list: linux [dash] iio [at] vger [dot] kernel [dot] org
- AD5380 IIO多通道Linux驅動程序DAC
- AD7291 IIO ADC Linux驅動程序
- AD5064 IIO四通道Linux驅動程序DAC
- AD5421 IIO DAC Linux驅動程序
- AD5360 IIO多通道Linux驅動程序DAC
- AD7303 IIO DAC Linux驅動程序
- AD5446 IIO DAC Linux驅動程序
- AD5764 IIO四通道Linux驅動程序DAC
- AD5624 IIO四通道Linux驅動程序DAC
- IIO單通道串行ADC Linux驅動程序
- AD9834 IIO直接數字合成Linux驅動程序
- AD9832 IIO直接數字合成Linux驅動程序
- AD7998 IIO ADC Linux驅動程序
- AD7887 IIO ADC Linux驅動程序
- AD5677R NanDAC+IIO Linux驅動程序
- 怎么編寫Framebuffer驅動程序 403次閱讀
- 自動刪除SDK/Vitis下驅動程序的舊版本的Linux腳本 558次閱讀
- 如何寫一個Linux設備驅動程序 4314次閱讀
- 米爾科技LINUX設備驅動程序教程 1967次閱讀
- 嵌入式Linux內核的驅動程序開發是怎樣的 1415次閱讀
- 淺談電腦驅動程序的工作原理 詳解電腦驅動程序意義 2.9w次閱讀
- 基于嵌入式Linux內核的系統設備驅動程序開發設計 1113次閱讀
- 基于Linux2.6.30開發DS18B20的驅動程序的類型和文件操作接口函數詳解 1377次閱讀
- 可動態安裝的Linux設備驅動程序 957次閱讀
- 如何用嵌入式Linux系統編寫鍵盤驅動 1312次閱讀
- 8255A驅動程序 3193次閱讀
- 8155驅動程序 3057次閱讀
- 深入了解USB驅動之總線驅動程序 8685次閱讀
- Xilinx設備的驅動程序 7967次閱讀
- PCI驅動程序開發實例 6702次閱讀
下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
評論
查看更多